Produse pentru componentă 2 epoxid (38)

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

DETAILING & PAINT CORRECTION

Accessoires Colle universelle de contact à pistoler à base de polychloroprène (Néoprène®) en canister spécial pour un pistolage immédiat sans la moindre installation de pistolage. Prête à l'emploi immédiatement et particulièrement écologique, utilisable avec un pistolet, ne nécessite pas d'air comprimé ou d'électricité, séchage et force d'adhérence initiale très rapides, rapide à mettre en oeuvre, pas d'entretien, toujours prêt à pistoler, très faible consommation, résistante à l'humidité, très haute résistance aux températures (jusqu'à +115°C), résistante aux acides et bases légers, sans toluène et chlorure de méthylène Accessoires 47100275 DISSOL SPRAY POUR COLLE CONTACT 500ML 47100612 CLEANING ADAPTOR NEOSPRAY - DISSOL SPRAY 47100615 FLEXIBLE NEOSPRAY 4M 47100620 PISTOLET NEOSPRAY 47100625 BUSE DE RECHANGE PISTOLET NEOSPRAY

Colle de contact transparente à base polyuréthane - spécial PVC doux Pour double encollage de matériaux divers, durs ou flexibles, comme la plupart des matières synthétiques (PVC souple, PVC, ABS, plexi, polycarbonate), bois, panneaux de revêtements décoratifs stratifiés, placage et collage sur champ, nez de marches et marches d’escalier, plinthes en PVC, cuir, liège, textile, métaux entre eux ou sur bois, pierre, béton, plâtre, métal et autres supports lisses et non poreux. Spécifiquement pour des applications dont la couche de colle ou le joint de colle reste visible : comme le collage sur verre ou plexi. Aussi idéal pour la réparation de bâches, toiles de tente et pour matériaux gonflables en PVC souple. Prête à l'emploi, transparente au séchage, pas de trace brune, utilisation aisée à la brosse et au peigne à colle, force d'adhérence progressive rapide, résistante à l'humidité à la chaleur et au froid (-10°C jusqu'à +70°C) Résiste aux acides légers et bases Sans...

Vopseaua Clorcauciuc pentru Pardoseli EMEX este un produs monocomponent, profesional, pe baza de emulsii de cauciuc clorurat, pigmenti, aditivi, plastifianti si solventi specifici, cu adaos de alfa corindon sau faina de cuartz pentru duritate. Produsul, foarte rezistent atat la apa cat si la frecare sau abraziune, are ca destinatie principala vopsirea pardoselilor din beton, fie pentru protejare, fie doar pentru marcare (eventual cu adaos de micro-perle din sticla). Vopseaua Clorcauciuc poate fi colorata in orice nuanta a cartelei RAL. Caracteristici principale: - Produs agrementat sanitar; - Aderenta ridicata la suport; - Aplicare si intretinere usoara; - Duritate excelenta; - Putere mare de acoperire; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la intemperii, factori chimici, frecare.

REFERENCE : ARTP3200TCR25 ALPHA 3200 coloré PLATRE 3200 T.CUITE ROUGE 25kg -> Descritpion PLATRE DE MOULAGE COLORE POUR L'INDUSTRIE STATUAIRE -> Domaine d'application Produit teinté, spécialement conçu pour l'industrie statuaire : - Moulages durs, - Maquettes, - Statuettes, et ornement. -> Caractéristique Unité de vente : bidon de 25kg Minimum de vente : un bidon

Acrystal prima liquide est un matériau composite blanc, sans solvant, à deux composants : - une résine acrylique liquide aqueuse "Acrystal Prima" - une poudre à base de cristaux minéraux : "Basic Crystal" -> Domaine d'application - Décorations architecturales - Répliques - Maquettes - Scénographie - Muséographie - Art &amp; artisanat - Modèles - Moules - Chapes de moule - Prototypes -> Caractéristiques Unité de vente : Pot de 25KG Minimum de commande : 1 pot Dosage en poids : 1 kg de liquide Acrystal Prima 2,5 kg de poudre Basic Crystal Dureté Shore D : 81 - 83 Temps de travail : 8 - 10mn